conductive polymer aluminum solid electrolytic capacitors cj series chip type, low esr, higher capacitance specifications temperature characteristics (max.impedance ratio) category temperature range rated voltage range rated capacitance range capacitance tolerance tangent of loss angle (tan ) esr (1) leakage current ( 2) performance characteristics item 55 to +105 c 2.5 to 16v 33 to 2700f 20% at 120hz, 20 c less than or equal to the specified value at 120hz, 20 c less than or equal to the specified value at 100khz, 20 c less than or equal to the specified value . after 2 minutes' application of rated voltage at 20 c z+105 c / z+20 c 1.25 (100khz) z 55 c / z+20 c 1.25 endurance damp heat (steady state) resistance to soldering heat marking the specifications listed at right shall be met when the capacitors are restored to 20 c after the rated voltage is applied for 2000 hours at 105 c. the specifications listed at right shall be met when the capacitors are restored to 20 c after the rated voltage is applied for 1000 hours at 60 c, 90% rh. after soldering the capacitor under the soldering conditions prescribed here, the capacitor shall meet the specifications listed at right, provided that it's temperature profile is measured at the capacitor top and the terminal. pre-heating shall be done at 150 to 200 c and for 60 to 180 sec. the duration for over +230 c temperature at capacitor surface shall not exceed 60 seconds. in the case of peak temp, less than 250 c, reflow soldering shall be two times maximum. in the case of peak temp, less than 260 c, reflow soldering shall be once. measurement for solder temperature profile shall be made at the capacitor top and the terminal. navy blue print on the case top capacitance change tan leakage current ( 2) esr (1) within 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value less than or equal to the initial specified value capacitance change tan leakage current ( 2) esr (1) within 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value less than or equal to the initial specified value capacitance change tan leakage current ( 2) esr (1) within 10% of the initial capacitance value ( 3) 130% or less than the initial specified value 130% or less than the initial specified value less than or equal to the initial specified value low esr, higher capacitance, high ripple current. load life of 2000 hours at 105 c. smd type : lead free reflow soldering condition at 260 c peak correspondence. compliant to the rohs directive (2002/95/ec). 1 esr should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 conditioning : if any doubt arises, measure the leakage current after the voltage treatment of applying dc rated voltage con tinuously to the capacitor for 120 minutes at 105 c. 3 initial value : the value before test of examination of resistance to soldering. p 1 c 2 j 3 0 4 j 5 2 6 2 7 1 8 m 9 c 10 l 11 1 12 g 13 s 14 configuration taping code size code capacitance toleranc ( 20%) rated capacitance ( 220 f ) rated voltage ( 6.3v ) series name type cj 220 j 841 h 0.3 max. d + 0.5 max. b 0.2 a 0.2 c 0.2 0.5 max. e l series voltage ( j:6.3v) plastic platform lot no. capacitance negative positive +0.1 -0.4 dimensions type numbering system (example : 6.3v 220f) voltage v 2.5 4 6.3 10 16 code e g j a c size d l a b c e h 5 6l 5.0 5.9 6.0 5.3 5.3 1.6 0.5 to 0.8 6.3 6l 6.3 5.9 7.3 6.6 6.6 2.1 0.5 to 0.8 6.3 8l 6.3 7.9 7.3 6.6 6.6 2.1 0.5 to 0.8 8 7l 8.0 6.9 9.0 8.3 8.3 3.2 0.8 to 1.1 8 8l 8.0 7.9 9.0 8.3 8.3 3.2 0.8 to 1.1 8 12l 8.0 11.9 9.0 8.3 8.3 3.2 0.8 to 1.1 8 10l 8.0 9.9 9.0 8.3 8.3 3.2 0.8 to 1.1 10 8l 10.0 7.9 11.0 10.3 10.3 4.6 0.8 to 1.1 10 10l 10.0 9.9 11.0 10.3 10.3 4.6 0.8 to 1.1 10 12.7l 10.0 12.6 11.0 10.3 10.3 4.6 0.8 to 1.1 (mm) dimension table in next page. cj cf low esr higher capacitance, ck low esr cat.8100y
conductive polymer aluminum solid electrolytic capacitors cj series standard ratings no marked, will be put at 12th digit of type numbering system. 1 taping specifications are given in page 23. recommended land size, soldering by reflow are given in page 18, 19. please refer to page 3 for the minimum order quantity. rated ripple current (marms) at 105 c 100khz rated capacitance ( f) rated voltage (v)(code) surge voltage (v) leakage current ( a) esr (m ? ) (at 100khz 20 c) rated ripple (marms) tan part number case size d l (mm) 2.5 (0e) 16 (1c) 10 (1a) 6.3 (0j) 4 (0g) 2.8 18.4 11.5 7.2 4.6 180 390 470 560 560 680 820 820 1000 1200 1500 1500 2200 2700 100 150 270 330 390 470 560 560 680 1000 1000 1200 1200 1500 1500 1800 1800 2200 100 120 220 270 330 330 390 470 820 820 820 1200 1500 1500 1800 47 56 68 120 150 220 270 330 390 470 680 33 39 68 82 100 100 120 150 180 220 220 270 330 90 195 235 280 280 340 410 410 500 600 750 750 1100 1350 80 120 216 264 312 376 448 448 544 800 800 960 960 1200 1200 1440 1440 1760 126 151 277 340 416 416 491 592 1033 1033 1033 1512 1890 1890 2268 94 112 136 240 300 440 540 660 780 940 1360 105 125 217 262 320 320 384 480 576 704 704 864 1056 21 15 13 13 13 13 12 9 12 13 10 9 10 9 22 22 15 15 14 14 14 9 13 10 13 9 10 9 10 10 9 9 24 24 15 14 14 14 14 13 12 10 13 12 12 10 11 28 28 28 25 21 21 21 19 17 19 13 35 35 28 24 24 24 24 22 18 18 22 16 16 2670 3400 3600 3600 4100 4100 4260 5400 4260 4800 5220 5400 5500 5800 2610 2610 3200 3300 3470 3950 4000 5200 3950 5220 4300 5400 5500 5200 5500 5500 5600 5700 2500 2500 3200 3470 3470 3950 3950 3950 4770 5150 4500 5025 5025 5500 5200 2310 2310 2310 2530 2880 3220 3220 3390 4000 3800 4820 2070 2070 2390 2700 2700 3010 3010 3150 3890 3890 3450 4070 4350 pcj0e181mcl1gs pcj0e391mcl1gs pcj0e471mcl1gs PCJ0E561MCL4GS pcj0e561mcl1gs pcj0e681mcl1gs pcj0e821mcl6gs pcj0e821mcl1gs pcj0e102mcl1gs pcj0e122mcl1gs pcj0e152mcl6gs pcj0e152mcl1gs pcj0e222mcl1gs pcj0e272mcl1gs pcj0g101mcl1gs pcj0g151mcl1gs pcj0g271mcl1gs pcj0g331mcl1gs pcj0g391mcl1gs pcj0g471mcl1gs pcj0g561mcl1gs pcj0g561mcl9gs pcj0g681mcl1gs pcj0g102mcl4gs pcj0g102mcl1gs pcj0g122mcl1gs pcj0g122mcl6gs pcj0g152mcl4gs pcj0g152mcl1gs pcj0g182mcl1gs pcj0g182mcl9gs pcj0g222mcl1gs pcj0j101mcl1gs pcj0j121mcl1gs pcj0j221mcl1gs pcj0j271mcl1gs pcj0j331mcl4gs pcj0j331mcl1gs pcj0j391mcl1gs pcj0j471mcl1gs pcj0j821mcl6gs pcj0j821mcl4gs pcj0j821mcl1gs pcj0j122mcl1gs pcj0j152mcl1gs pcj0j152mcl9gs pcj0j182mcl1gs pcj1a470mcl1gs pcj1a560mcl1gs pcj1a680mcl1gs pcj1a121mcl1gs pcj1a151mcl1gs pcj1a221mcl1gs pcj1a271mcl1gs pcj1a331mcl1gs pcj1a391mcl1gs pcj1a471mcl1gs pcj1a681mcl1gs pcj1c330mcl1gs pcj1c390mcl1gs pcj1c680mcl1gs pcj1c820mcl1gs pcj1c101mcl4gs pcj1c101mcl1gs pcj1c121mcl1gs pcj1c151mcl1gs pcj1c181mcl1gs pcj1c221mcl4gs pcj1c221mcl1gs pcj1c271mcl1gs pcj1c331mcl1gs 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 5 6 6.3 6 6.3 8 6.3 8 8 7 8 7 8 8 8 12 8 8 10 8 8 10 8 12 10 10 10 12.7 5 6 5 6 6.3 6 6.3 6 6.3 8 8 7 8 7 8 12 8 8 8 10 10 8 8 12 10 10 8 12 10 10 10 10 10 12.7 10 12.7 5 6 5 6 6.3 6 6.3 8 6.3 8 8 7 8 7 8 8 8 10 8 12 10 8 10 10 10 10 10 12.7 10 12.7 5 6 5 6 5 6 6.3 6 6.3 8 8 7 8 7 8 8 8 10 10 8 10 10 5 6 5 6 6.3 6 6.3 8 6.3 8 8 7 8 7 8 8 8 10 8 10 10 8 8 12 10 10 : in this case, will be put at 12th digit of type numbering system. 4 : in this case, will be put at 12th digit of type numbering system. 6 : in this case, will be put at 12th digit of type numbering system. 9 cat.8100y
|
